vp下载安卓

谷歌浏览器看不了youtube-ZOL问答:7条回答:【推荐答案】没有遇到过,你换下别的浏览器看看,或者删除谷歌浏览器的历史记录,并且断网重新连接一下。

Why make a clone of another board? First and foremost it is not a straight copy of he original. board, rather it is an improved version of the Huzzah32. The original has issues with the biggest two being the price and the power consumption in deep sleep mode. The current consumption in deep sleep mode is about 10uA. The battery voltage monitor is nearly identical to the original and has two 100k resistors in series with the center tap connected an ADC channel . In this design it would be the dominant power draw so I added a high side switch that disconnects the resistors from the LiPo-cell when the board is in sleep mode.

Other small changes are the addition of activity LEDs for the RX and TX signals of the USB to Serial converter, a cutout of the PCB underneath the printed antenna of the Wroom-32 module to restore the RF performance of the Wroom-32 module.

This entry was posted in Uncategorized on by Daniel.

vp下载安卓

AnalogRead does indeed work on the ESP32.  Many sites and posts that claim that the Analog to Digital converter of the ESP32 doesn’t work.  I have tested analogRead using the code below and it works as expected.  The code below compiles and downloads to my ESP32 Development board and produces correct results.  The input pin is the seventh pin from the top on the left hand side of the ESP32 Development Board.

#define RLED 16
#define InPin 33

int x ;
能访问youtube的浏览器
谷歌浏览器怎么上YouTube
   pinMode(RLED, OUTPUT);
}

x浏览器看YouTube
{
   digitalWrite(RLED, LOW);
   delay(100);
能访问youtube的浏览器
什么浏览器可众看油管
   digitalWrite(RLED, HIGH);
   delay(100);
}

Have fun!

This entry was posted in ESP32 on by Daniel.

vp下载安卓

I receive many questions in a week on the correct setup of the Arduino Environment to program the ESP32 development board.   At this point it doesn’t seem to matter which board you select and I always use “Esp32 Dev Module” as my selection.  The rest of the setting can be seen in the screen capture below.

x浏览器看YouTube

ESP32 Arduino Setup

The upload speed is fast and it works just like an Arduino board.  Press the upload button and the code magically appears in the module memory.  No buttons to press, just works.

This entry was posted in ESP32 on by 谷歌浏览器怎么上YouTube.

ESP32 Development Board-Again Part 2

猎豹加速器,连接你我:在使用公共 Wi-Fi、旅途中访问个人和工作账户、想要网络浏览记录的隐私性的时候,猎豹加速器 都可让您安枕无忧 我伔有所有主流操作系统都是适用 猎豹加速器 应用程序,主要支持 IOS 和 Android 系统。 并且只需要一个 猎豹加速器 账户,就可众同时使用 ...

为什么不能浏览国外网站:2021-6-13 · 这些奔驰独家圣诞礼物是小编在浏览海外网站时看到的,看完之后觉得非常有趣,所众和大家分享一下。 最让我吃惊的是,这款奔驰AMG平衡自行车,红色、白色和黑色车身颜色匹配,配有可调节座椅和12英寸小车轮,车身上还带有AMG标志。

This entry was posted in ESP32 on by Daniel.

ESP32 Development Board-Again

Here is the current version of the$16.95  ESP32 development board using an ESP-WROOM-32 module directly from Espressif.   My optimism about the availability of the ESP32S modules from AI-Thinker was misplaced.  I believe they are finally shipping now but since I haven’t seen any with my own eyes I remain unconvinced.  In the meantime, I switched to a module that is actually available in production quantities.

Top View of New PCB

The ESP32 board has a Espressif WROOM-32 module installed with the pinout marked on the PCB albeit in very small letters.    The PCB is routed out under the antenna for the best RF performance.  The WROOM-32 module is certified worldwide by the relevant authorities and has an FCC Id number.

Chrome浏览器优秀扩展插件推荐_懒得勤快的博客_互联网 ...:2021-3-28 · Google Chrome (83.0.4103.61)浏览器绿色优化增强版 Firefox浏览器78beta1 绿色优化增强版_x64 Chromium和Chrome强制所有网站允许Flash V2RayN简易使用教程 Chrome浏览器菜单和设置页提示“由贵单位管理”? v2ray+tls+websocket+cloudflare CDN安全的 is where you can buy some for $16.95 each.  The schematic is also available for download and there are a few example programs on the forum.

This entry was posted in New products on by Daniel.

ESP32 Development Board

It seems that most ESP32 breakout boards are vaporware or futureware.  I have been buying ESP8266 modules for some time and recently ordered ESP32S modules directly from AI-Thinker.  They started signing their email with “Notes:ESP-32 begin to sale!” and I assumed that it means that I can buy as many as I need.

I asked for a price for a few hundred modules, was quoted a price and when I placed an order I was told that they will ship me one module for development.  After some back and forward one became two and it was duely shipped with some ESP8266-07 modules that I use for some custom products and my breakout board.  http://www.ezsbc.com/index.php/featured-products-list-home-page/wifi01.html  A few weeks later I received an email saying that the ESP32S was now in stock and I ordered a few hundred with some ESP8266 modules.  That was about two months ago and I’m still waiting.

On Friday, 6 Jan 2017 I finally got a tracking number for my modules.

能看YouTube浏览器

Here is my brand new ESP32 development board.  Other than the ESP32 module it has an FTDI FT231XS USB to Serial converter, A 3.3V LDO, Reset and Flash Switches and a multi color LED.

浏览器不装这个插件,就是浪费!-黑马公社-二十次幂:2 天前 · 俗话说得好 “没有插件的Chrome没有灵魂”,给浏览器上插件,实现更多的功能,已经成了家常便饭,但并非所有插件都能轻易下到,有些过了期,有些有广告,有些会卡顿,有些占内存。 有没有一款插件能实现所有功能,同时占用又小呢?有这么一款“插件里的插件(套娃行为)”,叫 Tampermonkey油 ...

UPX浏览器:一款自带“你懂的上网”的浏览器 | 翻应用:2021-1-21 · UPX 浏览器 是四哥在逛谷歌市场无意中发现的,采用chrome内核,自带科学上网功能,可众轻松访问像谷歌、油管、非死不可等海外知名网站,畅想互联网知识,更能在91、1024上学习更多新姿势。 UPX 浏览器 完全免费,不限速、不限带宽,亲测速度很快,只是自带广告。

All the required capacitors and pull-up resistors are fitted on the board.  The board can be powered from an external power supply of up to 12V or the USB connector or both.

Unlike most other boards this one fits on a breadboard and has one row of pins accessible on each side of the board.

The schematic will be available once the board is listed for sale.  If you are interested in the board drop me a line at sales @ ezsbc.com

The board is expected to be available in volume by Jan 15, 2017 for $19.95 per board.

Edit: You can buy the boards here  for $16.95.  The board uses the ESP-WROOM-32 module instead of the AI-Thinker ESP32S module due to continuing supply problems with the AI-Thinker module.

This entry was posted in New products on by Daniel.

vp下载安卓

I recently described a board for hacking on OpenWrt and that also has connectors for adding USB peripherals and custom made PCBs.  The AR9331 board is described in the post immediately preceding this one.  Here I will describe the connectors in more detail.

The board has the following connectors:

  • Power Input
  • Two RJ45 Ethernet Ports
  • 2 Type A USB ports
  • 什么浏览器可众看油管
  • WiFi Antenna Port
  • The Expansion Connector

The Power Input is used for powering the board and the peripherals attached to the board including the USB Type A ports.  The board has a switch mode regulator to convert the input voltage to 5V at high efficiency.  A standard barrel socket is used with the center pin connected to positive and the outer sleave being ground.   The ideal input voltage is 12V since the efficiency is very high at 12V input but any voltage from 7V to 17V will work.  The 7V lower limit is dictated by the maximum duty cycle of the switching regulator.  The switching regulator is rated for 20V continuous but I prefer to not use input voltages higher than 17V to prevent spikes from killing the regulator.   The input voltage will spike if the power is unplugged while the board is drawing significant current.  There is a 1A PolyFuse is series with the input voltage to protect the PCB from damage if there is a short circuit somewhere on the board or USB plugs.

The RJ45 ports have integrated magnetics and the tabs for the cable connector point downwards.  Ordinary Cat5 and Cat5E cables can be used.

The two USB ports can both act as USB Host ports since there is a USB Hub on the board.  These USB ports can power external hard drives and other devices that draw significant current from the 5V supply.  The 5V in the USB is current limited at about 3A for both ports combined.  The power is available even if the device has not been enumerated.  Since these boards are aimed at being embedded inside other products the 5V from the USB can power external 5V devices including battery chargers.  We have tested several USB hard drives, flash drives and some other peripherals on the USB ports.  One of the devices known to work is a USB to Serial adapter based on an FTDI chip.  Similar boards normally can’t drive USB to Serial or USB to Parallel converters due to the compatibility issues of the AR9331 chipset with USB 1.1 devices.

Chrome浏览器优秀扩展插件推荐_懒得勤快的博客_互联网 ...:2021-3-28 · 不装扩展的 Chrome 只能发挥它 40% 的能力。各类实用的 Chrome 扩展是不少人选择 Chrome 浏览器的重要原因,经过多年发展,Chrome 的扩展种类已经非常丰富,除了那些「即装即用」的小工具之外,也有很多被誉为「神器」的强大扩展程序。1.油猴脚本

The WiFi port is a 50 Ohm 2.4GHz port for transmitting and receiving the WiFi signals.  The connector is a standard IPAX u.FL connector and you can connect any 50 Ohm antenna to the module.  These connectors are not designed for many mating cycles and a typical spec is 10 cycles.  The boards will be supplied with an antenna that is printed on a PCB but any standard 2.4GHz antenna will work.

The Expansion Connector is a 20-pin 0.1″ header connector and is not fitted on the modules.  The connector has a a number of signals that connect directly to the AR9331 SOC and they should be treated with care.  The AR9331 is a 2.5V device and its pins are NOT 3.3V or 5V tolerant.

 

1 GPIO15 GPIO18 2
3 谷歌浏览器怎么上YouTube 能看YouTube浏览器 4
5 Vin GPIO20 6
7 Gnd GPIO21 8
9 RXftdi GPIO22 10
11 TXftdi GPIO23 12
13 2.5V GPIO24 14
15 谷歌浏览器怎么上YouTube GPIO26 16
17 5V GPIO27 18
19 Gnd x浏览器看YouTube 20

 

Some of the pins have special functions assigned to them with hardware support for those functions and I will cover them later.  The 2.5V pin is provided more as a reference than a power supply pin.  You should not draw current from it.  The 3.3V pin can suply some current and I will qualify it in more detail in the future.  It is limited by the fact that there is no heatsink on the 3.3V LDO except for some copper areas attached to the device.  It this point I think 50mA should be available with a possibility of 100mA or even 150mA.  The 5V pin is the primary regulated supply and any board that needs more than a few mA should have a regulator from the 5V to generate its own supply voltage.  In the event that a module needs a voltage higher than 5V I routed the input voltage directly to the Vin pin but it is unregulated and untouched except for the PolyFuse protection.

  • GPIO15 is shared with a signal called LED4 on the AR9331 and the description reads “Ethernet switch LED3” and it defaults to a general purpose IO pin.
  • GPIO16 is shared with LED5 for which there is even less information available but it defaults to an IO pin.
  • GPIO18 can be configured as I2S_CK for an I2S audio inteface.
  • GPIO19 can be configured as I2S_WS for an I2S audio inteface.
  • GPIO20 can be configured as I2S_SD for an I2S audio inteface.
  • GPIO21 can be configured as I2S_MCK for an I2S audio inteface.
  • GPIO22 can be configured as I2S_MICIN for an I2S audio inteface.
  • GPIO23 can be configured as SPDIF_OUT for a digital audio output.
  • GPIO24 is always a general purpose IO-pin.
  • GPIO26 is a general purpose IO-pin that can be configured as a generic LED driver.
  • GPIO27 is a general purpose IO-pin that can be configured as a generic LED driver.
  • GPIO28 is a general purpose IO-pin that can be used to control and external Low Noise Amplifier for increased WiFi sensitivity. It is always available as an IO pin on this board.

The I2S Interface

I2S/SPDIF out is an audio interface that support up to 48 KHz sampling clock and a serial clock of more than 512 * sampling frequency. It also supports seamless switching of the audio out stream from I2S to SPDIF.  I2S MIC is also supported.  Can generate serial clock for various sampling frequencies.

 

 

 

 

This entry was posted in General, 什么浏览器可众看油管, 什么浏览器可众看油管 on by Daniel.

OpenWrt Atheros AR9331 Development Board

vp下载安卓

It is a low cost development board that lets you embed Linux into your projects. It runs OpenWrt with a Linux kernel, has 2 USB host ports and has full Ethernet and 802.11 b/g/n WiFi capabilities.

Applications:

  • Internet of Things
  • Voice over IP
  • Mesh WiFi
  • Industrial Control
  • Internet Radio
  • 谷歌浏览器怎么上YouTube

OpenWrt is a reliable Linux distribution for embedded systems with an emphasis on networking. It is open source, actively developed and well maintained. OpenWrt uses the OPKG package system, has lots of powerful utilities and the software is maintained in package form. Users can easily install, add and remove packages to make a very customized system.

AR9331 OpernWrt  Development Board

AR9331 OpernWrt Development Board

什么浏览器可众看油管

CPU: ATHEROS AR9331 chipset, which integrates MIPS 24Kc processor, CPU 400MHz, Hardware Ethernet Switch (MAC, PHY) and integrates with on chip MAC, RF, PA and LNA for WiFi.
谷歌浏览器怎么上YouTube 64MB;
Flash : 16MB
Interfaces: 2 x RJ45, 2 x USB Host, 1 x UART, 14 GPIOs
OS: Linux based OpenWrt
Power: 7 to 17 VDC power input with onboard switch mode regulator
WiFi: Support 150M 2.4Ghz WiFi, 802.11 b/g/n
Frequency range: 2.4~2.4835GHz
Modulation: BPSK, QPSK, CCK and OFDM (BPSK/QPSK/16-QAM/ 64-QAM)
Sensitivity @PER : 135M : -65dBm@10%PER; 65M : -65dBm@10%PER; 54M : -68dBm@10%PER; 11M : -84dBm@8% PER; 6M : -88dBm@10% PER; 1M : -90dBm@8% PER
x浏览器看YouTube Indoor: 60m (max); Outdoor 150m (max) (with 2 dBi antenna)
RF Power: 11n: 13dBm; 11g: 13-15dBm, 11b: 16-18dBm,
Antenna Connector: I-PEX connector.

Why?

Chrome浏览器优秀扩展插件推荐_懒得勤快的博客_互联网 ...:2021-3-28 · 不装扩展的 Chrome 只能发挥它 40% 的能力。各类实用的 Chrome 扩展是不少人选择 Chrome 浏览器的重要原因,经过多年发展,Chrome 的扩展种类已经非常丰富,除了那些「即装即用」的小工具之外,也有很多被誉为「神器」的强大扩展程序。1.油猴脚本

Hacking a router to install OpenWrt is a well tried path to getting a functional board with open source software to allow development of low volume or one-off projects.  It has its problems.  In most cases the schematics are not available unless someone took the trouble to reverse engineer the schematics from the printed circuit board.  The TL-WR703N has been reverse engineered and the schematics are available here . I looked at the schematics and they appear reasonable and are most likely correct or nearly so.  So again, why bother making a board based on the same chipset?  Part of the answer lies in our own requirements.  We wanted a board with more than one Ethernet port and a USB port to allow us to write data on a real hard drive.  The Raspberry Pi and the Beaglebone fail the two Ethernet port requirement although they have lots of USB ports available.  In some cases we want to turn off the radio and use only the wired ports for security reasons.  Also, routing Ethernet packets without hardware assistance is a CPU killer in terms of work load.  That still leaves the option of using a commercial router and hacking it.

There are many routers out there and may are well supported by OpenWrt, our preferred operating system.  Many have four or five Ethernet ports and some have USB ports as well.  Some testing has shown that we need 64M of RAM for our target application and that ruled out some routers.  The lower cost routers all seemed to be based on the AR9331 system on a chip and some testing on hacked boards lead to a remarkably annoying discovery.  You can have two identical routers with identical software and one will have a reliable USB port, one not.  Even worse, some have very low failure rates so they appear OK but will hang when left unattended.

Searching on the Internet for a fix showed that OpenWrt has a patch for the problem.  After making sure the patch was applied we tested a couple of boards and they worked well.  In fact, they worked so well that we considered the problem solved and started developing the application.  After some time a board that worked correctly acted up and would not be reliable with a hard disk attached to the AR9331 USB port.  We had previously tested this exact board with a hard drive and copied very large amounts of data from one place on the drive to another.  We also read the content of the entire drive, a few hundred gig without any problem whatsoever.  I tried another board with a physical hard drive and it worked fine but it absolutely refused to read an old USB Flash drive.  Searching on the Internet for a solution I saw a post somewhere that installing a passive USB hub between the chipset USB port and the drive (or keyboard, USB to UART adapter or some other devices) fixes the problem for some people.  We tried it and it worked! A flaky USB system became reliable. Two questions remained; Is it really fixed? and What is the cause?  There is a large topic on the OpenWrt forum that started in 2012 and is still going about this USB issue.  http://forum.openwrt.org/viewtopic.php?id=39956  There were many theories and suggestions including reading undocumented registers and writing the contents back periodically.  More searching and emails eventually crystallized into the following facts:

  • All AR9331 devices have a USB stability issue
  • It is not power supply related
  • Disabling the WiFi makes the problem go away
  • The problem can be solved by adding a USB 2.0 Hub between the AR9331 and the offending devices
  • USB 1.1 devices never work reliably.

为什么不能浏览国外网站:2021-6-13 · 这些奔驰独家圣诞礼物是小编在浏览海外网站时看到的,看完之后觉得非常有趣,所众和大家分享一下。 最让我吃惊的是,这款奔驰AMG平衡自行车,红色、白色和黑色车身颜色匹配,配有可调节座椅和12英寸小车轮,车身上还带有AMG标志。

I added a USB 2.0 Hub to the board and for good measure I added a second USB host port as well.  We now have reliable USB ports for anything recognized by the software.  Since one of our aims is to use physical hard drives attached to the USB ports I added a 5V 3A switch mode regulator to the board and wired the 5V directly to the two USB host ports.  The ports don’t respect the 100mA/500mA current limits of standard USB port and will happily supply 2A or more on a port as long as the total current drain is less than 3A.

The board has been undergoing testing now for a couple of weeks and it appears that all the bugs are now in the software.  All the parts are in house but the solder paste stencil is still in process.   The board will be available for purchase by the end of June 2015 and a single unit will be below $50.

This entry was posted in Interesting Products, New products on by Daniel.

12V TO3-style regulator available

The PSU6 is similar to the LM323 replacement in shape but produces 12V at 1A.  Since the TO3 package is no longer manufactured all the regulators in this package will disappear from the market in due course.

6 and 5s

PSU6 next to its older brother

 

The PSU6 has a 40V absolute maximum input voltage and will produce 1A without a heatsink.  It is mechanically identical to a LM7812K and is more accurate being within 2% of 12V under all load and input conditions.  It includes over current, thermal and short circuit protection.

One of  the improvements made to to the PSU6 based on user feedback is that the rings around the ground contacts have been increased in size.

PSU6s

PSU6 12V 1A switching regulator

 

This entry was posted in New products on by Daniel.

New Level Shifting Buffer, Level Shifter

I just finished the design and development of a new Level Shifter, LS2.  Although similar in function to the LS1 the new level shifter complements the functions of the LS1.

The  new Level Shifter is a true buffer, squaring up the input signal and driving the output signal high and low with active drivers.  The LS1 is a bi-directional circuit and drives low but has resistors for pull-up.  It is aimed at I2C circuits and low speed signals.

The LS2 outputs are low when the inputs are not driven.  Each one of the 12 inputs has a 500k pull down resistor to ground to ensure that the input will stay low while the micro driving it is in reset.  It works well with an Arduino to convert 5V or 3.3V signals to 12V.

LS2

LS12 showing inputs and outputs on the two sides.

The LS2 has two power supply pins, pin 1 and pin 28 and the buffers can translate from low to high levels or high to low levels.  The input and output power supplies determine whether the level shifting is from high to low or vice versa.  The input and output power supplies can be anywhere from 3.3 to 18V and the order in which the supplies are turned on is not important.

The LS2 has 12 channels with the inputs on the left and outputs on the right.

 

LS2 in a panel before being seperated

LS2 in a panel before being separated

X浏览器 - 超出您预期的小而强大:2021-3-10 · X浏览器并不完美,但是我伔一直在努力变得更好。 "X"是数学方程中的未知数,伕表着变化和迭伕,你看到的X浏览器是经过很多用户反馈意见和建议迭伕而成。同时X浏览器也在尽最大可能性提高其灵活性,希望为每一个用户变得不一样。

 

100kHz 50% duty cycle 5V square wave input.  Yellow is the input, Blue is the output signal

1MHz 50% duty cycle 5V square wave input.
Yellow is the input, Blue is the output signal

谷歌浏览器怎么上YouTube

Rising Edge – 50ns per division

 

x浏览器看YouTube

Falling Edge at 50ns per division

 

这21个油猴脚本推荐给你,让你的浏览器更好用更强大! - 简书:2021-9-15 · 你还在忍受百度搜索出现大量广告,没办法看爱奇艺等平台VIP视频,百度网盘低速下载,付费音乐无法下载,网页限制复制,购物无法比价,等等一系列让你烦恼的问题吗? 这些不方便的事情...

Production quantities are available now and the price is $4.95 for a 12-channel module.

This entry was posted in New products on by Daniel.

LM323K Replacement Now Available

In the previous post I said that with a little bit of luck the PSU5 would be in production by the end of May.  Well, the luck didn’t materialize and it took till the first week in June for it to be ready.  Even now my production capacity is a little limited due to a fault in the solder paste stencil.

MissingPasteS

From the picture above you can see that the inductor mounting pads did not get any paste.  The stencil file provided by the PCB supplier to the stencil manufacturer did not contain the openings for the inductor pads.  Normally paste openings are rectangular and because these were not strictly rectangles the CAM program dropped them from the paste mask.  The supplier is re-manufacturing the stencil and for the time being the paste for the inductors are being added with a manual paste dispenser.  Fortunately the pads are large so it is easy to do.  A long story short; The LM232K replacement is called PSU5 and is available for sale from the shop.  See http://www.ezsbc.com/index.php/products/psu5.html

This entry was posted in New products on by Daniel.

vp下载安卓

The first prototypes of the LM323 Replacement were difficult to manufacture.  In particular the trim resistor would not pick correctly in my pick and place machine.  The hole in the center of the adjustment ring was big enough to allow enough air to leak so that it kept falling off the nozzle when the placement head accelerated.  I substituted the trimmer with a different brand and the problem is resolved.

PSU5 next the an original LM323

PSU5 next the an original LM323

发个能直接上facebook,youtube等网站的浏览器,需要的下 ...:2021-3-30 · 这个软件也是论坛一位FY发的。当时他说能云端支持FLASH。我想装那个FLASH的插件对FLASH不是很完美的支持。于是就下了他。这个浏览器确实能完美的支持。只是网页显示效果不太好。不过凑合着用了。然'.....

百分浏览器 - 追求速度、简约和安全的网络浏览器:2021-4-23 · 百分浏览器是一款众快速和实用为目标的Chrome增强版浏览器,它紧跟最新版Chrome 内核,不断增强办公和娱乐相关的上网体验。 首页 更新日志 功能介绍 常见问题 扩展中心 关于 论坛 64位安装版 立即下载 版本号:4.2.10.171 内核版本:80.0.3987.163 ...

The pins of the LM323 Replacement is the same diameter as the original but slightly shorter

The pins of the LM323 Replacement is the same diameter as the original but slightly shorter.

 

x浏览器看YouTube

The LM323 Replacement is a little lower in profile the the original ensuring that it will fit everywhere.

This entry was posted in New products on by Daniel.

LM323 Replacement

For all of my pinball and video game customers I have a new product in the works.  Many of the pinball and video game consoles use LM323K devices as 5V regulators.  As many of you may know the LM323 has now been discontinued by all the manufacturers and prices are beginning to skyrocket.  This was a very popular and long lived part so there is probably many parts sitting in inventory at many companies so supplies won’t disappear overnight.

In many applications the LM323 is hard to substitute since it is a high current regulator rated at 3A.  I made a PCB with the same footprint as the LM323 and it contains a switch mode voltage regulator.谷歌浏览器怎么上YouTube

This is a photograph of one of the first prototype boards still in the panel.  Unlike any of the other three pin regulators this one contains a trim resistor.   Even though the accuracy of this design is +- 2% instead of the +-5% of the original LM323 I included the trimmer to allow fine adjustment of the output voltage.  In many applications where the LM323 were/are being used the 4.75V minimum voltage of the LM323 caused problems so people made arrangements to increase the voltage by some other means.  By allowing the voltage to be fine tuned I hope to ensure compatibility with all the existing applications.

The LM323 replacement is designed with components rated at 4A.  The bottom of the PCB contains only the ground connection, same as the LM323.  The neat rows of vias are thermal connections between the top and bottom of the PCB.  One of the items that has to wait for the production PCB is the final current rating of the LM323 replacement without a heatsink and with the small heatsinks found on some PCB’s.  It will be better than the original but the aim is to reach 3A continuous from a 12V input without a heatsink.  The copper on the prototype PCB’s is only 35 micron thick and that limits the thermal performance.  The production PCB’s will have 70 micron copper to help with heat conduction from top to bottom.  All the filter capacitors are on the PCB.  The height of the assembly is 4mm above the PCB or 5.6mm total measured from the bottom of the PCB to the top of the highest component.  The exposed areas of the copper is coated with nickel and gold to prevent corrosion even in very hard conditions.

Production quantities should be available by the end of May 2014 with pricing for single units at around $8 and discounts for volume purchases.

This entry was posted in x浏览器看YouTube on by Daniel.

Really Low Cost GPS Module

I have always been surprised by the high price of GPS modules that provide a location and a time reference.  There is a module developer seeking funding on Indiegogo for a sub $15 module that has a modern GPS receiver and CPU on a tiny PCB.  For details see this link 华为浏览器不能网页看youtube - 荣耀V10问题反馈 花粉俱乐部:2021-1-31 · 华为浏览器不能网页看youtube [复制帖子标题和链接] 7628 17 即将的光芒 略有小成 发表于 2021-1-29 10:18:51 来自:荣耀V10 我AI的快 最新回复 2021-1-31 18:15:33 首先不是网络问题,我就在国外,然后我看半年前就有人 ...

I would like to see this project succeed so please tell your 5000 closest friends about it.

 

 

This entry was posted in Interesting Products on by Daniel.

‘New’ 3-Pin Regulator Design

Some people noticed that the first Power Supply Module to appear on the site was named PSU2.  This oddity was due to design named PSU1 turned out to be remarkably difficult to assemble with a decent yield.  The PSU2 was designed to fill the immediate need for 5V and 3.3V switching regulators that are drop in replacements for linear three pin regulators such as the 7805 but without the headache of the heatsink.  This is particularly true when the supply voltage is 12V.  Even at 500mA load current the heatsink is embarrassingly large.   The design of the PSU2 was done in a short time and it is a very successful design that has very low ripple and noise.  The switching frequency is high to keep the filter components small.  The two limitations of the PSU2 is that the input voltage range is restricted to 17V maximum and that is less than the original 7805 family and the highest output voltage available is 5V, again lower than the original 7800 family.

The PSU1 design overcomes these limitations while keeping the same form factor as the PSU2.  The only difference in the mechanical size is the PSU1 has a larger inductor.

Panel1sb

The photograph above shows a panel of the PSU1 design after reflow and test.  This was the third panel assembled and the first one with 100% yield.  For those unfamiliar with assembly details this is a good example of the challenges of manufacturing small PCB’s on automatic equipment.  To be able to place the components the Pick and Place machine needs some clearance to the edge of the board and must be able to hold the board.  The strips on the outer edge are commonly referred to as ‘thieves’ (I don’t know why) and allow the machine to hold the pane and populate components up to the edge of the individual  PCB’s.  On these strips there are a few holes and copper dots.  The dots are to allow the P&P machine to determine the exact position of the panel and to correct for variations in the routing of the panel.  The dots are called ‘fiducial marks’ and are sometimes placed near fine pitch devices to allow for accurate placement of those IC’s.  The vertical lines between the individual PCB’s are ‘v-scores’ to allow the boards to be separated after assembly and in this case after testing as well.  There are limitations to the smallest size of board that can be scored and this panel can not be scored exactly next to the PCB’s due to these limitations.  The small sections of board are inserted into the panel to allow the board edges to be scored even though the blades can not be set to the width of the individual PCB’s.  By adding these small sections the board edges can be scored by passing the panel through the scoring machine twice.

The holes on the corners of the panel to allow precise alignment in my solder paste printer.  The printer has pins that exactly fit the holes and the repeatability from panel to panel is as good as the registration of the holes to the copper.  To ensure proper soldering on this design was remarkably hard.  The IC is a ball grid device with a fine pitch and it has to be mounted in close proximity to the inductor.  The noise increases and efficiency decreases as the inductor is moved further away from the away from the IC.  The mass of the inductor prevents that part of the board from heating as fast as the rest of the board and may lead to poor solder joints underneath the IC where it is impossible to inspect without x-rays.  Solder paste consist of metal, flux and other magic sauce that gives it the properties required to print correctly, not slump after printing and solder properly.  To judge the solder volume and alignment I made a test panel where the diagonals were populated with components and then it went through the reflow oven.

什么浏览器可众看油管

The photo above is of the partially populated panel after it went through the reflow oven.  Note how small the dots are for the BGA part.

 

PanelTest1SectionS

 

This is a photo showing a close-up of four boards with two populated and two unpopulated boards.  With a microscope and some patience the solder volume on each pad can be calculated and the uniformity of the deposition can be evaluated.  To limit the amount of paste placed on the inductor pads the stencil has two openings for each pad.  I thought the paste would flow together but it clearly does not.  In this case it does not matter because there is enough solder on the pads and once the inductor is placed in the paste it does solder uniformly.  It does highlight the need to be sure that a QFN package is pressed down firmly enough into the solder to make sure the solder covers the entire pad underneath the IC since the solder does not seem to flow horizontally but prefers to make ‘bumps’.  From this photograph it is also really easy to see how small and tightly spaced the balls are on this package.

This design has a 40V input limit and eventually there will be 9V and 12V variants available.  For now the 5V and 3.3V are available in production quantities.

To emphasize how small the board is it is shown next to a LM7805.

PSU1_Comparison_S

 

 

 

This entry was posted in New products on by 谷歌浏览器怎么上YouTube.

EzSBC1 20% Price Reduction

We have experienced increased sales across all our products but the standout is the EzSBC1 where sales have risen consistently as the module gets designed into more products.  With the increased volume comes a reduction in costs, the CPU and PCB being the two items with largest price reduction in absolute terms.  Starting from 4 Nov 2013 the price for the EzSBC1 BASIC Programmable Controller drops to $39.95 for singles and $35.95 for orders of ten or more.  Educational prices do not change.  Full details at http://ezsbc.com/index.php/products/ezsbc1.html

 

This entry was posted in General and tagged BASIC, Embedded on by Daniel.

能看YouTube浏览器

I have run into a problem with the decoder software.  I have read many posts on how to turn the keyboard LEDs on and off but they stubbornly remain off.  Normally interfaces to a PC are extensively documented by multiple sources and widely available.  I’m surprised by how little accurate information is available.  This includes some waveforms (diagrams, not captures) that have the wrong number of clock pulses in the transmitted data.  I have been busy recently and unable to work on the issue but during the past week I got back to it and rewrote the code to toggle the LED once more and it still doesn’t work.

Since I can’t find reliable information I will have to measure it.  I bought a few cables, connectors and set up a test PC to talk to the keyboard.  I will capture the waveforms and publish them here so that there is a trustworthy source of information.

Daniel

This entry was posted in New products on by Daniel.

vp下载安卓

A message I posted on the forum about the vulnerability of the programs store in a programmable device created a lot interest and e-mail.  Many e-mails asked for more information on vendors who can read programs from devices with the security bits blown.  I don’t want to encourage piracy so I don’t respond to these requests with more information.  Recently a YouTube video of a presentation on Low-Cost Chip Microprobing was brought to my attention.  It has some details on how chips are protected and how the protection is circumvented.  The talk can be found here 【灵狐浏览器】-博文推荐-CSDN博客:2021-4-8 · csdn已为您找到关于灵狐浏览器相关内容,包含灵狐浏览器相关文档伕码介绍、相关教学视频课程,众及相关灵狐浏览器问答内容。为您解决当下相关问题,如果想了解更详细灵狐浏览器内容,请点击详情链接进行了解,或者注册账号与客服人员联系给您提供相关内容的帮助,众下是为您准备的相关 ...

This entry was posted in Security on by 谷歌浏览器怎么上YouTube.

vp下载安卓

We have been working on a comprehensive PS/2 keyboard controller.  PS/2 keyboards are available in many shapes, sizes and specialty versions and most are low cost as well.  A problem with these keyboards are that they require fairly complicated code to read the data from the keyboard and translate it into a simple ASCII character.

There are a few PS/2 controllers on the market so why build another one?  The short answer is that none of the ones on the market meet our needs.  Most (All?) PS/2 controllers produce 5V signals and this is a problem for modern CPU’s that run on 3.3V.  The output ports available on the existing controllers are typically serial ports and some offer I2C interfaces.  We will offer serial, I2C and SPI outputs, simultaneously.  The power supply to the microcontroller is switchable between 3.3V and 5V to allow the keyboard decoder to be used with 3.3V and 5V systems without level shifters.  We also offer IO pins that signal when there is a character available, when the internal buffer is full and the state of the Caps Lock of the keyboard.

The first prototype had a few issues such as the PS/2 connector had to be soldered onto the bottom of the board, the reset signal was broken and some other minor issues.  The second prototype is in much better shape and we are coding away furiously.  Once the board and the code is fully tested it will be for sale at a reasonable price.  The schematic will be available to everyone  and the source code will be available to all who purchase the controller.  You will be able to modify the code to suit your own personal requirements.  The decoder is programmable without any hardware and with free software.  The CPU is quite capable and fast and has several IO pins available so you may be able to fit your entire project onto the controller.

 

This entry was posted in New products on by Daniel.

能访问youtube的浏览器

I try to never be out of stock but I managed to get the 5110 LCD’s to sell out before my stock arrived.  I didn’t plan well enough for the Chinese New year and its effect on delivery and shipping.  A batch of displays arrived today and another, smaller batch is on its way as well.

I ordered some new items that may be of interest to some of our users and after I’ve tested and photographed them they will appear as regular stock items.

Daniel

This entry was posted in General on by Daniel.